BMW E90 E91 E92 Manual Drive Shaft Propshaft 325d 330d N57 7580555

BMW E90 E91 E92 Manual Drive Shaft Propshaft is an original drivetrain component designed for installation in the rear section of vehicles equipped with a manual transmission. Thanks to factory geometry and precise balancing, it ensures stable torque transfer from the gearbox to the rear differential, which translates into confident handling and predictable vehicle behavior. This solution is dedicated to users who expect consistency with the original BMW design and the maintenance of proper drivetrain operating standards.

Specifications and technical data

• SKU: 7580555
• Mark: BMW (Genuine OE)
• Condition: Used
• OEM Part Number: 7580580
• Substitutable numbers: 26107580555, 7580555, 26107614434, 7614434, 26107580580, 7580580
• Location on the vehicle: Rear
• Gearbox type: Manual
• Category: Drivetrain Hardware & Fasteners

Purpose and compatibility with the BMW drivetrain

The presented drive shaft has been designed to work with the N57 engine in BMW 3 Series E90 and E92 models in 325d and 330d versions, in a manual transmission configuration. Its placement in the rear of the vehicle makes this component responsible for linear, stable power delivery to the rear axle, which is crucial for maintaining the typical BMW handling characteristics. Using an original part from the Drivetrain mounting parts and brackets category allows you to maintain compliance with the vehicle's factory design specifications.

Construction, installation, and performance characteristics

The drive shaft in this BMW model operates under demanding conditions – it transfers high torque generated by the N57 diesel engine while maintaining adequate stiffness and resistance to torsional vibrations. The use of an original design ensures:

• proper balancing across the entire RPM range,
• stable cooperation with the manual transmission,
• proper fitment to factory brackets and supports in the chassis,
• maintenance of drivetrain alignment.

As a result, the risk of vibrations, knocking, or unwanted play, which could occur when using components inconsistent with the manufacturer's design, is reduced. A used, original drive shaft is a good choice for repairs where maintaining factory operating parameters is a priority.

Benefits of using an original BMW drive shaft

Using a dedicated drive shaft in a BMW E90/E92 with an N57 engine and manual transmission allows for maintaining the integrity of the entire drivetrain. The most important advantages include:

• Factory fitment – compatibility with original brackets, supports, and flanges in the vehicle.
• Predictable car behavior – no need for structural modifications, maintaining stock handling characteristics.
• Optimal cooperation with the rear differential and manual gearbox – reduction of stress and unwanted tension in the system.
• Ability to use existing mounting points – facilitating service work and reducing replacement time.

For users who drive their BMW dynamically, maintaining the drive shaft in proper condition has a direct impact on ride comfort, noise levels, and the durability of other drivetrain components. Choosing an original component helps avoid problems resulting from inaccurate fitment or improper balancing.

Selecting parts by OEM and interchangeable numbers

When selecting a drive shaft for a specific BMW 3 Series configuration with an N57 engine, it is crucial to use the OEM part number and interchangeable numbers, which allow for verifying the component's compatibility with a specific body, drivetrain, and transmission version. In practice, this means the ability to precisely match the component to the car without the risk of installing the wrong variant. Verification by factory numbers is particularly important in the case of used drivetrain elements, where structural differences between individual versions may not be visible at first glance.

If you want to deepen your knowledge about selecting original parts by OEM numbers and VIN, as well as learn practical tips regarding work with engines, the article on our blog will be helpful: Audi five-cylinder engine – a legend from Quattro to RS3 and how to take care of it using original Audi parts. Although it describes a different manufacturer, the principles of identification and selection of OEM parts presented there are universal and can be successfully applied to BMW service as well.

Expanding the BMW drivetrain

If you are planning a comprehensive repair or upgrade of the drivetrain area in your BMW and need other elements from the same group, such as brackets, mounts, or additional fasteners, check out the available parts in the BMW drivetrain mounting parts and brackets category.